Plumbing Basics: Before Installing a Bathtub
Plumbing Basics: Before Installing a Bathtub
Blog Article
Do you find yourself on the lookout for content concerning Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't precisely brain surgery, however it does need strong plumbing, woodworking, and occasionally, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately difficult job. If the old tub is readily accessible, the task can move speedily; if you need to open up a wall surface to eliminate the old tub and place the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will require a helper to move out the old bathtub and also embeded in the new one. See to it you have qualified on your own for the job and also fit attempting it. Instead of employing a service provider to take over a halfway-completed job, it is better to think about using one prior to you start. Opportunities are you may require a professional plumber to make tube connections.
This post will help you mount a brand-new bath tub in your bathroom if you have actually already purchased a new tub as well as do not need to transform the plan of your previous water system pipes.
Your tools and also product checklist ought to consist of the following:
Preparing for the Installment
First of all, the sustaining frame provided with the bath ought to be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to avoid strain on the tub.
Fit the versatile tap ports to the bottom of both faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite bothersome due to the restricted gain access to that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have been removed, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning during this process. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before proceeding to fit the new taps, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, place the tub in the required setting. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also changing the feet on the tub until the level reads level.
To install taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water system and also inspect all joints and also new pipework for leakages and tighten them if necessary. Load the bath tub as well as also examine the overflow electrical outlet as well as the normal outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the maker's instruction manual. Tiling and sealing around the bath tub should wait up until the bath tub has actually been utilized a minimum of once as this will certainly resolve it right into its last position.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the placing hole in the bath/basin guaranteeing that the washers are in area in between the faucet as well as the sink. Safeguard the tap in position with the manufacturer provided backnut. Once the tap is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical tap connectors. The former kind must be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break an inflexible seal, causing the water to permeate the wall surface in between the bath and also the tiling, resulting in difficulties with dampness and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes and also cartridges, and are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill the tub with water prior to securing, to permit the activity experienced when the tub is in usage. The sealer can fracture fairly early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water-proof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
We had been shown that report on How to Install a Bathtub Yourself from an associate on a different web property. Loved our piece of writing? Please share it. Let other people locate it. Bless you for your time. Please visit our website back soon.
Expertise available here. Report this page